ACCESSGARD™ security glazing is laminated glass constructed with a state-of-the art proprietary material that is built to withstand extensive physical attack during a forced-entry scenario. It provides the aesthetics and daylighting advantages of glass, with an additional level of security.
| ACCESSGARD Security Glazing |
ACCESSGARD-2118 Security Glazing |
|||
|---|---|---|---|---|
| Download | PDF Specification | PDF Specification | PDF Specification | |
| Thickness | 5/16” | 3/8” – 1/2″ | 9/16” | |
| Availability | Available for ONLY retrofit monolithic and interior | Available for monolithic and insulated glass units | Available for monolithic and insulated glass units | |
| Maximum Size | less than 20 sq. ft. | 72 x 130* | 60 x 96* | |
| Weight | 3.68 lbs./sq. ft. | 4.16 – 5.80 lbs./sq. ft. | 4.95 lbs./sq. ft. | |
| Standard Compliance | Forced Entry | ASTM F1233-08 Class 1.3 | ASTM F1233-08 Class 1.3 | ASTM F1233-08 Class 1.4 |
| Test Duration | 6 min 47 sec | 6 min 47 sec | 17 min | |
| Safety | ANSI Z97.1, CPSC 16 CFR 1201 (Cat. I and II), Hurricane Compliant | |||
| Manufacturing | ASTM C 1036, ASTM C 1048, ASTM C 1349, ASTM C 1172 | |||
| Options | Clear | Tinted Glass, Reflective Glass, Fire-Rated Glass, Low-E Glass, Insulating Glass Units | ||
*Actual glass thickness may vary due to glass size options and design loads.
Global Security Glazing offers a wide range of security glazing products to protect a wide variety of buildings, including high-performance forced-entry and bullet-resistant constructions that can be installed in lobbies, access points, shelters, transactional windows and other areas where heightened security is desired.
| GOOD | BETTER | BEST | |
|---|---|---|---|
| ACCESSGARD SECURITY GLAZING | ATTACK RESISTANT | BULLET RESISTANT | |
| Cost | $ | $$$ | $$$$ |
| Level of protection |  |
 |
 |
| Thickness | 5/16” | 7/16” – 1 1/4″ | 3/4” – 2 1/4” |
| Construction | Laminated security glass | Glass-CladPoly w/ glass on exposed surfaces | Glass-CladPoly w/ Poly on safe side. All glass make-ups available. |
*Actual glass thickness may vary due to glass size options and design loads.
| TEST SEQUENCE | TEST IMPLEMENTS | # OF IMPACTS | SEQUENCE TIME (SECONDS) | CLASS ACHIEVED | NOTES |
|---|---|---|---|---|---|
| 1 | Ball-Peen Hammer | 10 | 22 | 1.0 | One technician delivered 10 impacts with a Ball-Peen Hammer, no penetration or openings were created. |
| 2 | Ball-Peen Hammer | 10 | 24 | 1.1 | A second technician delivered 10 additional impacts with a Ball-Peen Hammer, no penetration or openings were created. |
| 3 | 1 1/2″ Diameter Pipe / 12-lb Sledge | 25 | 174 | 1.2 | One technician held the pipe while one technician swung a 12-lb Sledge Hammer. The pipe was held at different angles to evaluate the resistance of the sample to both puncture and gouging. |
| 4 | Extinguisher, CO2 | NA | 60 | 1.3 | Extinguisher fully discharged for 60 seconds. This step is designed to freeze the materials, mimicking cold weather and making the components more brittle for subsequent attack. Other products in the market avoid this step. |
| 5 | Sledge Hammer | 25 | 44 | 1.4 |
ACCESSGARD: ACCESSGARD-2118: |
| 6 | Propane Flame Torch | 300 | 1.5 | ACCESSGARD-2118: The propane torch was used IAW ASTM F1233-08, Section A1.5.2. The flame was continuously applied and was held such that the blue tip of the torch flame was no further than 1-in from the surface of the sample. The flame was initially held at the location of the hole that allowed the 1/8-in contraband rod to pass through at the completion of Sequence 5. The sample material began to melt and the torch flame was used to enlarge the opening. At the conclusion of this sequence, a fine mist of water was used to extinguish the still-burning material. The Forced-Entry Shape was able to pass through the hole created during this sequence. |
Class Achieved: ASTM F1233-08 Class 1.3
Test Duration: 6 Minutes, 47 Seconds
Class Achieved: ASTM F1233-08 Class 1.4
Test Duration: 17 Minutes
See installation and cleaning instructions.
Please note that only the glazing has been tested to the attack tools, techniques, methods, testing procedures and durations detailed in ASTM F 1233-08, Class 1.3 and 1.4. GSG makes no warranty, and claims no responsibility for any loss, damage or claim for any tools, devices, techniques, or methods used, or any attack duration not otherwise detailed in ASTM F 1233-08, Class 1.3 and 1.4. ACCESSGARDTM security glass products were also tested to additional non-industry standard test protocols. Please contact us for more details at accessgard@isoclimasg.com or 866.412.6977.
